PowerShell

Additional Load Balancing rule to Existing Azure Load Balancer

By |2020-09-03T06:55:15+00:00March 22nd, 2017|AzureVM, PowerShell|

Suppose we have an existing Load Balancer and we need to an additional load balancing rule in it. In such case we can use below azure power shell commands to implement the same. The commands we used are comes under   "AzureRM.Network"  Module for Azure Resource Manager. Save the new configuration by using Set-AzureLoadBalancer.

Setup load balancer on Azure VMs

By |2020-09-03T07:12:29+00:00March 21st, 2017|AzureVM, PowerShell, Windows|

An Azure load balancer is a Layer-4 (TCP, UDP) load balancer. Usually a load balancer gave distributed traffic among VMs in it even if one VM is in down state. I prepared this article by referring the old Azure doc related to Load balancer.  So use it for setting up load balancer on azure

Additional NAT rules to Existing Load Balancer and attach to NIC VM

By |2020-09-03T07:13:20+00:00March 19th, 2017|AzureVM, PowerShell|

Here we are going to add Nat rules to existing Azure load balancer . After that attach these NAT rules to an different NIC we have for the load balanced VM. I used Power shell AzureRM Network command  to add additional NAT rules. Now you can see new load-balanced NAT rules are added.

Disable backing Up status for HyperV VM R1Soft

By |2020-07-26T07:12:53+00:00March 16th, 2017|Hyper-V, PowerShell, Windows|

In this blog post we are trying to explain how to disable backing up status for hyperv vm durig R1soft backing period. For that we need to Disable the ” checkpoint ”  option available for VM from the settings tab or by restarting the service “Hyper-V Virtual Machine Management service” Some times its necessary

How to create Availability Set for Azure VM

By |2020-09-03T07:16:25+00:00March 6th, 2017|AzureVM, PowerShell, Windows|

By default it’s not necessary to have an Availability set for creating a new VM.  But Availability set is necessary if you are going to attach this VM to a load balancer.  We have to set the Availability set at the time of creation of VM.  At this moment it’s not possible to attach

How to create new Azure VM using Powershell commands

By |2020-09-03T07:17:11+00:00March 6th, 2017|AzureVM, PowerShell|

Refer below steps for creating new azure vm using powershell commands comes under AzureRM Network. Before we proceed with creation of VM we need below resources in our azure accounts and the information regarding our existing account. If it’s not available create it. Resource Group A storage Account Our account Geographical Location NIC card

How to change subnet for azure virtual machines ( asm-arm) NIC card

By |2020-09-03T07:18:09+00:00February 28th, 2017|AzureVM, PowerShell|

Subnet change of VM is only possible if the both subnet are in the same vnet.  Virtual network change of an existing VM is not possible at this moment. Need to delete the VM and create it again. We used old AzureRM Network powershell commands. Refer this article for how to change subnet for

How to Change Existing NIC-AzureVM

By |2020-09-03T07:18:55+00:00February 9th, 2017|AzureVM, PowerShell|

The number of NIC cards supported by Azure VMs depends on Azure VM size(VM plans).  If we would like to add new NIC card to an Azure VM which only supports one NIC cards, need to remove the existing one. In such cases, we need to follow below methods. I used AzureRM.Network powershell commands

How to Add Additional NIC to Azure VM

By |2020-09-03T07:21:16+00:00February 6th, 2017|AzureVM, PowerShell|

Here I am using the Resource Manager and AzureRM.Network Powershell to add new NIC on existing VMs.  Use it for add additional nic to azure vm whether you are still maintains  old AzureRM module. Please note that multiple NICs are only supported by few VM plans (VM size). So before proceeding with adding a

Go to Top